The Series RLC Circuit
Thus far we have seen that the three basic passive components, R, L and C
have very different phase relationships to each other when connected to
a sinusoidal AC supply. In a pure ohmic resistor the voltage waveforms
are “in-phase” with the current. In a pure inductance the voltage
waveform “leads” the current by 90o, giving us the expression of ELI. In a pure capacitance the voltage waveform “lags” the current by 90o, giving us the expression of ICE.
This
Phase Difference, Φ depends upon the reactive value of the components being used and hopefully by now we know that reactance, (
X
) is zero if the circuit element is resistive, positive if the circuit
element is inductive and negative if it is capacitive thus giving their
resulting impedances as:
Element Impedance
| Circuit Element |
Resistance, (R) |
Reactance, (X) |
Impedance, (Z) |
| Resistor |
R |
0 |
 |
| Inductor |
0 |
ωL |
 |
| Capacitor |
0 |
 |
 |
Instead of analysing each passive element separately, we can combine
all three together into a series RLC circuit. The analysis of a
series RLC circuit is the same as that for the dual series
RL and
RC circuits we looked at previously, except this time we need to take into account the magnitudes of both
XL and
XC
to find the overall circuit reactance. Series RLC circuits are classed
as second-order circuits because they contain two energy storage
elements, an inductance
L and a capacitance
C. Consider the RLC circuit below.
Series RLC Circuit
The series RLC circuit above has a single loop with the instantaneous
current flowing through the loop being the same for each circuit
element. Since the inductive and capacitive reactance’s
XL and
XC are a function of the supply frequency, the sinusoidal response of a series RLC circuit will therefore vary with frequency,
ƒ. Then the individual voltage drops across each circuit element of
R,
L and
C element will be “out-of-phase” with each other as defined by:
- i(t) = Imax sin(ωt)
- The instantaneous voltage across a pure resistor, VR is “in-phase” with the current.
- The instantaneous voltage across a pure inductor, VL “leads” the current by 90o
- The instantaneous voltage across a pure capacitor, VC “lags” the current by 90o
- Therefore, VL and VC are 180o “out-of-phase” and in opposition to each other.
For the series RLC circuit above, this can be shown as:
The amplitude of the source voltage across all three components in a
series RLC circuit is made up of the three individual component
voltages,
VR,
VL and
VC
with the current common to all three components. The vector diagrams
will therefore have the current vector as their reference with the three
voltage vectors being plotted with respect to this reference as shown
below.
Individual Voltage Vectors
This means then that we can not simply add together
VR,
VL and
VC to find the supply voltage,
VS
across all three components as all three voltage vectors point in
different directions with regards to the current vector. Therefore we
will have to find the supply voltage,
VS as the
Phasor Sum of the three component voltages combined together vectorially.
Kirchoff’s voltage law ( KVL ) for both loop and nodal circuits
states that around any closed loop the sum of voltage drops around the
loop equals the sum of the EMF’s. Then applying this law to the these
three voltages will give us the amplitude of the source voltage,
VS as.
Instantaneous Voltages for a Series RLC Circuit
The phasor diagram for a series RLC circuit is produced by combining
together the three individual phasors above and adding these voltages
vectorially. Since the current flowing through the circuit is common to
all three circuit elements we can use this as the reference vector with
the three voltage vectors drawn relative to this at their corresponding
angles.
The resulting vector
VS is obtained by adding together two of the vectors,
VL and
VC and then adding this sum to the remaining vector
VR. The resulting angle obtained between
VS and
i will be the circuits phase angle as shown below.
Phasor Diagram for a Series RLC Circuit
We can see from the phasor diagram on the right hand side above that
the voltage vectors produce a rectangular triangle, comprising of
hypotenuse
VS, horizontal axis
VR and vertical axis
VL – VC Hopefully you will notice then, that this forms our old favourite the
Voltage Triangle and we can therefore use Pythagoras’s theorem on this voltage triangle to mathematically obtain the value of
VS as shown.
Voltage Triangle for a Series RLC Circuit
Please note that when using the above equation, the final reactive
voltage must always be positive in value, that is the smallest voltage
must always be taken away from the largest voltage we can not have a
negative voltage added to
VR so it is correct to have
VL – VC or
VC – VL. The smallest value from the largest otherwise the calculation of
VS will be incorrect.
We know from above that the current has the same amplitude and phase
in all the components of a series RLC circuit. Then the voltage across
each component can also be described mathematically according to the
current flowing through, and the voltage across each element as.
By substituting these values into Pythagoras’s equation above for the voltage triangle will give us:
So we can see that the amplitude of the source voltage is
proportional to the amplitude of the current flowing through the
circuit. This proportionality constant is called the
Impedance of the circuit which ultimately depends upon the resistance and the inductive and capacitive reactance’s.
Then in the series RLC circuit above, it can be seen that the opposition to current flow is made up of three components,
XL,
XC and
R with the reactance,
XT of any series RLC circuit being defined as:
XT = XL – XC or
XT = XC – XL with the total impedance of the circuit being thought of as the voltage source required to drive a current through it.
The Impedance of a Series RLC Circuit
As the three vector voltages are out-of-phase with each other,
XL,
XC and
R must also be “out-of-phase” with each other with the relationship between
R,
XL and
XC being the vector sum of these three components thereby giving us the circuits overall impedance,
Z. These circuit impedance’s can be drawn and represented by an
Impedance Triangle as shown below.
The Impedance Triangle for a Series RLC Circuit
The impedance
Z of a series RLC circuit depends upon the angular frequency,
ω as do
XL and
XC If the capacitive reactance is greater than the inductive reactance,
XC > XL
then the overall circuit reactance is capacitive giving a leading phase
angle. Likewise, if the inductive reactance is greater than the
capacitive reactance,
XL > XC
then the overall circuit reactance is inductive giving the series
circuit a lagging phase angle. If the two reactance’s are the same and
XL = XC then the angular frequency at which this occurs is called the resonant frequency and produces the effect of
resonance which we will look at in more detail in another tutorial.
Then the magnitude of the current depends upon the frequency applied to the series RLC circuit. When impedance,
Z is at its maximum, the current is a minimum and likewise, when
Z is at its minimum, the current is at maximum. So the above equation for impedance can be re-written as:
The phase angle,
θ between the source voltage,
VS and the current,
i is the same as for the angle between
Z and
R
in the impedance triangle. This phase angle may be positive or negative
in value depending on whether the source voltage leads or lags the
circuit current and can be calculated mathematically from the ohmic
values of the impedance triangle as:
Series RLC Circuit Example No1
A series RLC circuit containing a resistance of
12Ω, an inductance of
0.15H and a capacitor of
100uF
are connected in series across a 100V, 50Hz supply. Calculate the total
circuit impedance, the circuits current, power factor and draw the
voltage phasor diagram.
Inductive Reactance, XL.
Capacitive Reactance, XC.
Circuit Impedance, Z.
Circuits Current, I.
Voltages across the Series RLC Circuit, VR, VL, VC.
Circuits Power factor and Phase Angle, θ.
Phasor Diagram.
Since the phase angle
θ is calculated as a positive value of 51.8
o
the overall reactance of the circuit must be inductive. As we have
taken the current vector as our reference vector in a series RLC
circuit, then the current “lags” the source voltage by 51.8
o so we can say that the phase angle is lagging as confirmed by our mnemonic expression
“ELI”.
Series RLC Circuit Summary
In a
series RLC circuit containing a resistor, an inductor and a capacitor the source voltage
VS is the phasor sum made up of three components,
VR,
VL and
VC
with the current common to all three. Since the current is common to
all three components it is used as the horizontal reference when
constructing a voltage triangle.
The impedance of the circuit is the total opposition to the flow of
current. For a series RLC circuit, and impedance triangle can be drawn
by dividing each side of the voltage triangle by its current,
I. The voltage drop across the resistive element is equal to
I x R, the voltage across the two reactive elements is
I x X = I x XL – I x XC while the source voltage is equal to
I x Z. The angle between
VS and
I will be the phase angle,
θ.
When working with a series RLC circuit containing multiple
resistances, capacitance’s or inductance’s either pure or impure, they
can be all added together to form a single component. For example all
resistances are added together,
RT = ( R1 + R2 + R3 )…etc or all the inductance’s
LT = ( L1 + L2 + L3 )…etc this way a circuit containing many elements can be easily reduced to a single impedance.
In the next tutorial about
Parallel RLC Circuits
we will look at the voltage-current relationship of the three
components connected together this time in a parallel circuit
configuration when a steady state sinusoidal AC waveform is applied
along with the corresponding phasor diagram representation. We will also
introduce the concept of
Admittance for the first tim
sir your blog helps me alot..............
ReplyDelete