Wednesday, September 13, 2017

Types of electrical insulators



Advertisement:

Electrical Insulators - Insulating Materials And Different Types

Purpose of an insulator is to prevent the unwanted flow of current from the energized conductor or conducting parts. Electrical insulation plays a vital role in every electrical system. Anelectrical insulator provides very high resistance so that practically no current can flow through it.

Insulating Materials

Basically, an insulating material or insulator contains a very small amount of free electrons (charge carriers) and, hence, could not carry electrical current. But, a perfect insulator does not exist, because even insulators contain a small number of charge carriers which may carry leakage current (negligibly small). In addition, all insulators become conductive when sufficiently large voltage is applied. This phenomenon is called as insulation breakdown and the corresponding voltage is called asbreakdown voltage.
An insulating material must have high resistivity and high dielectric strength. Additional desirable properties of insulating material depend on the type of applications. Insulating material used for manufacturing insulated cables/wires must be flexible such as rubber or PVC. On the other hand, insulator used to supportoverhead power lines must be mechanically strong, such asporcelain or glass insulators.

Important Properties Of Insulating Materials

  • Resistivity (specific resistance) is the property of a material that quantifies how strongly the material opposes to flow of electric current. Resistivity of a good insulator is very high.
  • Dielectric strength of a material is the ability to withstand electric stresses without breaking down. Dielectric strength is usually quoted in kilovolts per millimeter (kV/mm).
  • Relative permittivity (or dielectric constant) is the ratio of the electric flux density produced in the material to that produced in vacuum.
  • Electrical dissipation factor (dielectric loss) is the ratio of the power lost in the material to the total power transmitted through it. It is given by the tangent of the loss angle and, hence, also known as tan delta
Some of the commonly used electrical insulating materials are paper, mica, teflon, rubber, plastic, polyvinyl chloride (PVC), glass, ceramic, porcelain etc.

Types Of Electrical Insulators

  • Pin insulators
  • Suspension insulators
  • Strain insulators
  • Shackle insulators
The above types of insulators are commonly used in overhead power lines. You can read more about theseoverhead line insulators by clicking this link.
Some more types of insulators are as follows.

Post Insulators

A post insulator is more or less similar to a pin insulator. It has relatively higher number of petticoats and rain sheds. Post type insulators are mostly used in substations, but in some cases, they can be used for overhead lines also. Thus, there are two types of post insulators: (i) Station post insulators and (ii) Line post insulators.
post insulators
Image source: Wikimedia commons
A line post insulator can be used for voltages up to 132 kV (pin insulators are used for up to 33 kV). Station post insulators are used in substations for low as well as very high voltages. For higher voltage levels, multiple station post insulators are stacked together.

[Also read: Basics of power transmission system]

Glass Insulators

Pin type glass insulators were earlier used in the 18th century primarily for telegraph/telephone lines. Use of ceramic and porcelain insulators spread in the 19th century. They proved superior protective properties than glass and become widely used. However, use of toughened glass insulators is becoming popular today. Unlike porcelain or non-ceramic materials, toughened glass never ages, and thus, offers a longer lifespan. Toughened glass insulator discs can be used in suspension insulators.
glass insulator string
Glass insulator string

Polymer Insulators

Polymer insulators are composed of a fibre glass rod covered by polymer weather sheds. Polymer weather sheds are generally made from sillicon rubber. Few other materials may also be used for weather sheds, such as polytetrafluorethylene (PTFE or Teflon), EPM, EPDM etc. Polymer insulator are sometimes also called ascomposite insulators or silicon rubber insulators. They are almost 90% lighter than porcelain insulators and still offer almost equal or better strength.
polymer insulators
Polymer insulators

Long Rod Insulators

A long rod insulator is basically a porcelain rod with an outside weather shed and metal end fittings. The main advantage of long rod design is the elimination of metal parts between the units, thereby increasing the insulator's strength. Long rod insulators can be used at suspension locations as well as tension locations.
long rod insulator
Long rod insulator
Image source: Wikimedia commons

Stay Insulators

The insulator used in a stay wire (guy wire) is called as stay insulator. It is usually made up from porcelain and is designed so that in case of breakage of the insulator, the stay wire will not fall to the ground. It is also called asegg-type strain insulator.
stay insulator
Stay Insulator
Image source: Wikimedia commons



Thursday, March 2, 2017

CLASSIFICATION OF ELECTRICAL DRIVES


The classification of electrical drives can be done depending upon the various components of the drive system. Now according to the design, the drives can be classified into three types such as single-motor drive, group motor drive and multi motor drive. The single motor types are the very basic type of drive which are mainly used in simple metal working, house hold appliances etc. Group electric drives are used in modern industries because of various complexities. Multi motor drives are used in heavy industries or where multiple motoring units are required such as railway transport. If we divide from another point of view, these drives are of two types:


    Reversible types drives

    Non reversible types drives.


This depends mainly on the capability of the drive system to alter the direction of the flux generated. So, several classification of drive is discussed above.



Parts of Electrical Drives

The diagram which shows the basic circuit design and components of a drive, also shows that, drives have some fixed parts such as, load, motor, power modulator, control unit and source. These equipments are termed as parts of drive system. Now, loads can be of various types i.e they can have specific requirements and multiple conditions, which are discussed later, first of all we will discuss about the other four parts of electrical drives i.e motor, power modulator, source and control unit.
Electric motors are of various types. The DC motors can be divided in four types – shunt wound DC motor, series wound DC motor, compound wound dc motor and permanent magnet DC motor. AC motors are of two types – induction motors and synchronous motors. Now synchronous motors are of two types – round field and permanent magnet. Induction motors are also of two types – squirrel cage and wound motor. Besides all of these, stepper motors and switched reluctance motors are also considered as the parts of drive system.



So, there are various types of electric motors, and they are used according to their specifications and uses. When the electrical drives were not so popular, induction and synchronous motors were usually implemented only where fixed or constant speed was the only requirement. For variable speed drive applications, DC motors were used. But as we know that, induction motors of same rating as a DC motors have various advantages like they have lighter weight, lower cost, lower volume and there is less restriction on maximum voltage, speed and power ratings. For these reasons, the induction motors are rapidly replaced the DC motors. Moreover induction motors are mechanically stronger and require less maintenance. When synchronous motors are considered, wound field and permanent magnet synchronous motors have higher full load efficiency and power factor than induction motors, but the size and cost of synchronous motors are higher than induction motors for the same rating.

Brush less DC motors are similar to permanent magnet synchronous motors. They are used for servo applications and now a days used as an effcient alternative to DC servo motors because they don’t have the disadvantages like commentation problem. Beside of these, stepper motors are used for position control and switched reluctance motors are used for speed control.

 Power Modulators - are the devices which alter the nature or frequency as well as changes the intensity of power to control electrical drives. Roughly, power modulators can be classified into three types,


    Converters,

    Variable impedance circuits,

    Switching circuits.


As the name suggests, converters are used to convert currents from one type to other type. Depending on the type of function, converters can be divided into 5 types -


    AC to DC converters

    AC regulators

    Choppers or DC - DC converters

    Inverters

    Cycloconverters


AC to DC converters are used to obtain fixed DC supply from the AC supply of fixed voltage. The very basic diagram of AC to DC converters is like.
ac to dc converter
AC Regulators are used to obtain the regulated AC voltage, mainly auto transformers or tap changer transformers are used in this regulators.
ac to ac converter
Choppers or DC - DC converters are used to get a variable DC voltage. Power transistors, IGBT's, GPO's, power MOSFET's are mainly used for this purpose.

dc to dc converter
Inverters are used to get AC from DC, the operation is just opposite to that of AC to dc converters. PWM semiconductors are used to invert the current.

dc to dc converter
Cycloconverters are used to convert the fixed frequency and fixed voltage AC into variable frequency and variable voltage AC. Thyristors are used in these converters to control the firing signals.
ac to ac converter

Variable Impedance circuits are used to controlling speed by varying the resistance or impedance of the circuit. But these controlling methods are used in low cost DC and ac drives. There can be two or more steps which can be controlled manually or automatically with the help of contactors. To limit the starting current inductors are used in AC motors.
Switching circuits in motors and electrical drives are used for running the motor smoothly and they also protects the machine during faults. These circuits are used for changing the quadrant of operations during the running condition of a motor. And these circuits are implemented to operate the motor and drives according to predetermined sequence, to provide interlocking, to disconnect the motor from the main circuit during any abnormal condition or faults.

Sources may be of 1 phase and 3 phase. 50 Hz AC supply is the most common type of electricity supplied in India, both for domestic and commercial purpose. Synchronous motors which are fed 50 Hz supply have maximum speed up to 3000 rpm, and for getting higher speeds higher frequency supply is needed. Motors of low and medium powers are fed from 400 V supply, and higher ratings like 3.3 kv, 6.6 kv, 11 kv etc are provided also.

Control Unit -
Choice of control unit depends upon the type of power modulator that is used. These are of many types, like when semiconductor converters are used, then the control unit consists of firing circuits, which employ linear devices and microprocessors.
So, the above discussion provides us a simple concept about the several parts of electrical drive.

Advantages of Electrical Drives

Electrical drives are readily used these days for controlling purpose but this is not the only the advantage of Electrical drives. There are several other advantages which are listed below -


    These drives are available in wide range torque, speed and power.

    The control characteristics of these drives are flexible. According to load requirements these can be shaped to steady state and dynamic characteristics. As well as speed control, electric braking, gearing, starting many things can be accomplished.

    The are adaptable to any type of operating conditions, no matter how much vigorous or rough it is.

    They can operate in all the four quadrants of speed torque plane, which is not applicable for other prime movers.

    They do not pollute the environment.

    They do not need refueling or preheating, they can be started instantly and can be loaded immediately.

    They are powered by electrical energy which is atmosphere friendly and cheap source of power.


Because of the above mentioned advantages of electrical drives, they are getting more and more popular and are used in a wider range of applications.


 Like13




« Previous
Next »
Closely Related Articles
What is Electrical Drive?
Electric Motor Power Rating
Motor Duty Class and its Classification
Thermal Model of a Motor
Induction Motor Braking Regenerative Plugging Dynamic Braking of Induction Motor
Induction Motor Drives | Starting Braking Speed Control of Induction Motor
DC Motor Drives
Dynamics of Electrical Drives
Interfacing of Stepper Motor
Control of Electrical Drives
Synchronous Motor Drives
Hysteresis Motor
Stepper Motor Drive
Bipolar Stepper Motor
More Related Articles
What is Braking? Types of Braking | Regenerative Plugging Dynamic Braking
Types of Braking in a DC Motor
What is Servo Motor?
Servomechanism | Theory and Working Principle of Servo Motor
Servo Motor Control
DC Servo Motors | Theory of DC Servo Motor
Servo Motor Controller or Servo Motor Driver
Servo Motor Applications in Robotics Solar Tracking System etc
Variable Frequency Drive or VFD
New Articles
Ideal Diode
Diode Current Equation
Toroidal Transformer
Voltage Doubler
Diode

Monday, February 13, 2017

Circuit breakers

For the protection of electrical equipment and for safe operation we use
Circuit Breaker

An air circuit breaker for low-voltage (less than 1,000 volt) power distribution switchgear
A two-pole miniature circuit breaker
Four one-pole miniature circuit breakers
Molded-case or miniature circuit breaker

A circuit breaker is an automatically operated electrical switch designed to protect an electrical circuit from damage caused by excess current, typically resulting from an overload or short circuit. Its basic function is to interrupt current flow after a fault is detected. Unlike a fuse, which operates once and then must be replaced, a circuit breaker can be reset (either manually or automatically) to resume normal operation. Circuit breakers are made in varying sizes, from small devices that protect low-current circuits or individual household appliance, up to large switchgear designed to protect high voltage circuits feeding an entire city. The generic function of a circuit breaker, RCD or a fuse, as an automatic means of removing power from a faulty system is often abbreviated to ADS (Automatic Disconnection of Supply).

Origins
Operation
Arc interruption
Short-circuit
Standard current ratings
Types of circuit breakers
    Sulfur hexafluoride circuit breaker